Ancient Crystal Golem 

Summoned from the depths of forgotten caverns, the Ancient Crystal Golem is a towering elemental guardian forged from rare arcane-infused crystals. Its jagged form radiates with ancient energy, and every step reverberates like cracking stone. Designed for FDM 3D printing, this figure showcases sharp crystalline armor, chunky limbs, and imposing symmetry, perfect for tabletop battles or as a stunning collectible.

Printing Recommendations:

• Printer Type: FDM
• Supports: Required (especially under arms and crystal spikes)
• Detail Level: Optimized for high-resolution 0.12 mm layer height
• Scale Options:
  • Small (28mm scale) – 35 mm tall
  • Medium (Heroic scale) – 50 mm tall
  • Large (Boss scale) – 75 mm+ tall

 Dungeons & Dragons 5e Stat Block

Ancient Crystal Golem
Large Construct, Unaligned

Armor Class: 19 (natural crystal armor)
Hit Points: 210 (20d10 + 100)
Speed: 30 ft.

Saving Throws: Con +9, Wis +4
Damage Resistances: Bludgeoning, Piercing, Slashing from nonmagical attacks
Damage Immunities: Poison, Psychic, Radiant
Condition Immunities: Charmed, Exhaustion, Frightened, Paralyzed, Poisoned
Senses: Darkvision 60 ft., Tremorsense 60 ft., Passive Perception 10
Languages: Understands Terran but cannot speak
Challenge: 11 (7,200 XP)

 Traits

Crystalline Form. Any creature that hits the golem with a melee weapon attack takes 1d6 slashing damage from the jagged shards.

Magic Resistance. The golem has advantage on saving throws against spells and other magical effects.

Crystal Pulse (Recharge 5–6). The golem releases a surge of radiant energy in a 15-foot radius. Each creature of the golem’s choice in that area must make a DC 16 Constitution saving throw, taking 4d10 radiant damage on a failed save, or half as much on a success.

 Actions

Multiattack. The golem makes two slam attacks.

Slam. Melee Weapon Attack: +10 to hit, reach 5 ft., one target.
Hit: 18 (2d10 + 7) bludgeoning damage.

 Optional Variant: Crystal Shards (Legendary Action)

Shard Volley (Costs 2 Actions). The golem launches crystal shards in a 60 ft. cone. Each creature in that area must make a DC 15 Dexterity saving throw or take 5d6 piercing damage and be slowed (as the slow spell) until the end of its next turn.

     Guide

Each of my models is printed 2-3 times before releasing the profile. So if you have a problem with printing:

1. DRY THE FILAMENT
2. CHANGE THE NOZZLE TO A NEW ONE.

Recommendations  Guide : In case of a problem with damage to the supports, I recommend reducing the printing speed of the supports by 30-50% and the travel speed to 400mm/s. When removing the supports, I recommend first cutting off the pieces right next to the character, but not removing them, just cutting them off. Remove the remaining larger pieces and only then detach the remaining smaller pieces. This reduces the risk of damaging delicate elements.

• Please note that if you use a different filament than the recommended one, the effect may be different from my print. For example, printing in silk PLA will look better but the supports and the print itself will be more brittle and less durable.

   

  Recommendations:

• 
   
• 0.08-0.2. In the event of changing the original height, the height of the supports should be changed.
   

• PLA+HS, PLA+, PLA, PLA silk Recommended materials are listed in order from best to good.

  

   

• Clean the plate thoroughly before printing.
  Make sure the filament is dry and free from dirt. This can damage the print or weaken the support